6s 20A PCM BMS for 24V Li-ion/Lithium/ Li-Polymer 18V LiFePO4 Battery Pack with Bluetooth, I2c, RS232, RS485 Communication Protocol (PCM-L06S20-G02)
Product Description
Technical parameter
Product name:Protection Circuit Module
Model No:PCM-L06S20-G02
For 6S Lithium-ion/Lithium Polymer/LiFePO4 Battery Packs
Product Feature:
1. Suitable for 6 section Lithium-ion/Lithium Polymer/LiFePO4 Battery Packs;
2. Connect the special upper computer software to display the total voltage, battery voltage, capacity, current, temperature, cycle times and other parameters;
3. Support HDQ or I2C communication protocol;
4. The metering IC adopts TI BQ34Z100 series, which can read voltage, capacity, current, temperature, cycle times and other parameters;
5. Over charge, over discharge, short circuit, over current, temperature protection, etc.;
6. The maximum continuous working current is 20A, and the charge and discharge are at the same port;
| Protection Circuit Module Specifications For 22.2V Li-ion/Li-Po Battery Pack | |||
| No | Test item (Test at normal temperature 25±2ºC and relative humidity≤90%) | Criterion | |
| 1 | Communication Interface | HDQ or I2C | |
| 2 | Capacity | Designing battery capacity(PCM) | 13Ah |
| Max capacity(Battery pack) | 290000mAh | ||
| Min capacity(Battery pack) | 100mAh | ||
| External capacity Indication | LCD,LED | ||
| Gas gauge algorithm | IT (High accuracy) | ||
| 3 | Voltage | Charging voltage(6S) | DC: 25.2V CC/CV(4.2V/1cell) |
| Cell-balance detection voltage (Charge balance) | 4.2V±0.03V | ||
| Cell-balance release voltage | 4.2V±0.025V | ||
| Cell-balance detection delay time | 0.96~1.4s | ||
| 4 | Current | Balance current for single cell | 42±5mA |
| Normal operating-mode current (Gas Gauge IC) | 2-0 uA | ||
| SLEEP operating-mode current (Gas Gauge IC) | 100 uA | ||
| FULL SLEEP operating-mode current (Gas Gauge IC) | 30 uA | ||
| Maximal continuous charging current | 20A | ||
| Maximal continuous discharging current | 20A | ||
| 5 | Over charge Protection | Over charge detection voltage | 4.25±0.025V |
| Over charge release voltage | 4.05±0.05V | ||
| Over charge detection delay time | 10~200ms(can adjust) | ||
| 6 | Over discharge protection | Over discharge detection voltage | 2.5±0.07V |
| Over discharge release voltage | 3.3±0.1V | ||
| Over discharge detection delay time | 0.5~2S(can adjust) | ||
| 7 | Over current protection | Over current detection voltage | 0.2±0.015V |
| Over current detection current | 50±10A(can adjust) | ||
| Detection delay time | 5~60mS(can adjust) | ||
| Release condition | Cut load , | ||
| 8 | Short protection | Detection condition | Exterior short circuit |
| Detection delay time | 200-800us | ||
| Release condition | Cut load , | ||
| 9 | Resistance | Protection circuitry (MOSFET) | ≤50mΩ |
| 10 | Temperature | Operating Temperature Range | -40~+85ºC |
| Storage Temperature Range | -40~+125ºC | ||
| Dimension | L105*W65*T5mm | ||
| B+:Battery+ | |||
| B-:Battery- | |||
| SDA:Serial Data interface | |||
| SCL:Serial Clock interface | |||
| HDQ:Open drain HDQ Serial communication line (slave) | |||
| P+:Charge+/discharge+ | |||
| P-:Charge-/discharge | |||